After you’ve assembled the equipment required to repair the laptop screen, it is time to begin to repair your device. Set the laptop closed onto the surface that you selected and keep the tools close by.
Take power sources off
Turn off your laptop, and ensure that it’s not connected to any power source to reduce any chance of electroshock. In addition, it helps to take out the battery in order to prevent any other problems.
After you’ve done this, you will need to find the stickers that cover the screws that are on the screen’s bezel. You will usually see them on the bottom of the laptop screen, near where hinges would be if the display opened.
Take care to remove screws and stickers
After that, you’ll have to pin to take off the labels that are on the bezel to ensure you don’t damage the bezel. It is necessary to apply these in the future, once your screen is installed correctly therefore, make sure that you don’t lose them and you keep them on the sticky side up, so that you can reuse the stickers. Keep them in a secure location so that when you are ready to connect the new laptop screen they’re easily accessible.
Then, you’ll need to use a screwdriver to take out the screws which are now visible. It’s possible to have some trouble depending on the degree to which they were screwed into when they were made. Most of the time If your old screen is aligned well, it shouldn’t pose difficult to get the screws out. Set them aside in the dish , making sure you don’t damage any.
Remove Laptop Screen bezel
It’s time to remove the bezel. Be careful in removing the screen’s bezel as it will be necessary to replace it after the screen has been replaced. With a putty knife or another flat object, you’ll be able to remove your screen from the laptop case. Check out the 15.6 inch laptop display price.
It could take a bit of effort to get it out completely. Be cautious when you hear the sound of plastic snapping. This is the release of the tabs made of plastic which hold the laptop screen to the case. If you’re having difficulty taking off the old screen, the screws on the bottom may not be loose enough, so you should stop and loosen them a bit before trying another time.
There are also problems with your laptop screen getting stuck to the hinges. If you gently move it you will usually be able to remove it from the frame.
Detach the LCD
One of the most difficult aspects of replacing your laptop screen will be taking off the LCD. Make sure the bezel is removed completely to allow you full accessibility to your LCD. It is anchored to the frame of the laptop’s aluminum frame and you’ll need to remove it from both sides.
There are two more screws to be removed from the top corners, before you are able to lift the laptop screen a bit away from the frame. There will likely be additional screws that secure the LCD to the sides. They must also be removed. In certain cases it is possible that heavy duty tape be used in lieu.
Unplug the cables from the connectors
Once you have removed the screen’s attachments, it will now be on top of your keyboard. It’s difficult to ensure there’s sufficient space in between your LCD and frame, but be cautious to not damage the video cable running across the front of the display and into the laptop’s body. If the cable is damaged you’ll need professional assistance in repairing it.
The next step is to disconnect the LCD’s cable. The connectors on the top of the screen but they could also be found in the lower part of the laptop screen. There is a good chance that glue was utilized to join both, and you’ll need to gently pull one off of the other. There might also be tape that has to get removed. However, in the end it’s pretty easy to remove your monitor from your video port. It should be placed far from the tools.
Install the new screen
After you have removed the laptop screen and then put it back in place, you should be able to determine the place where your new screen will be. Put it on the floor within the frame, so that it will fit perfectly. Once you have it in place, attach the video connector again so that it’s placed exactly where the original LCD was. Be sure to make sure it’s in the best alignment possible, then connect it using adhesive or tape.
Reattach bezel
Once you’ve finished, make sure that the sides are secured. Reinstall the screws onto the edges and on top or reconnect any tape used to keep everything in place. After everything is properly fitted, you are able to place the screen back in. It should be aligned in a way that it is firmly inserted into the case of the screen and can’t be difficult to loosen.
Re-insert the screws in the bezel once you’re sure everything is securely snapped into the right place. You shouldn’t discern any cracks around any edges on the screen. After the screws have been inserted then reattach the screw covers with a needle or pin.
Power up
Then, you’ll be able to restart your computer. Install the battery as well as connect the computer to a source of power before turning it on. If there’s no display, then you’ll have to confirm to ensure that everything was assembled.
Enjoy a great DIY laptop screen repair
Repairing the screen of your laptop does not have to be completed by an expert. If you’ve got the time and desire, you could save yourself a considerable amount by performing the repair yourself by knowing the laptop display price. If you follow these steps, you’ll be able to get your laptop’s display running within one or two hours.
References
https://www.hp.com/us-en/shop/tech-takes/diy-laptop-screen-repair